Free CCNA 200-301 Dumps 2026

 

Refer to the exhibit. How does the router manage traffic to 192.168.12.16?

A. It chooses the EIGRP route because it has the lowest administrative distance.
B. It load-balances traffic between all three routes.
C. It chooses the OSPF route because it has the longest prefix inclusive of the destination address.
D. It selects the RIP route because it has the longest prefix inclusive of the destination address.

 

 

What are two reasons for an engineer to configure a floating static route? (Choose two.)

A. to enable fallback static routing when the dynamic routing protocol fails
B. to route traffic differently based on the source IP of the packet
C. to automatically route traffic on a secondary path when the primary path goes down
D. to support load balancing via static routing
E. to control the return path of traffic that is sent from the router

 

 

Refer to the exhibit. How does router R1 handle traffic to 192.168.10.16?

A. It selects the IS-IS route because it has the shortest prefix inclusive of the destination address
B. It selects the RIP route because it has the longest prefix inclusive of the destination address
C. It selects the OSPF route because it has the lowest cost
D. It selects the EIGRP route because it has the lowest administrative distance

 

 

Refer to the exhibit. A router reserved these five routes from different routing information sources.
Which two routes does the router install in its routing table? (Choose two)

A. OSPF route 10.0.0.0/30
B. IBGP route 10.0.0.0/30
C. OSPF route 10.0.0.0/16
D. EIGRP route 10.0.0.1/32
E. RIP route 10.0.0.0/30

 

 

Refer to the exhibit. To which device does Router1 send packets that are destined to host 10.10.13.165?

A. Router2
B. Router3
C. Router4
D. Router5

 

 

R1 has learned route 10.10.10.0/24 via numerous routing protocols. Which route is installed?

A. route with the next hop that has the highest IP
B. route with the lowest cost
C. route with the lowest administrative distance
D. route with the shortest prefix length

 

 

Which two minimum parameters must be configured on an active interface to enable OSPFV2 to operate? (Choose two.)

A. OSPF process ID
B. OSPF MD5 authentication key
C. OSPF stub flag
D. IPv6 address
E. OSPF area

 

 

Refer to the exhibit. What commands are needed to add a subinterface to Ethernet0/0 on R1 to allow for VLAN 20, with IP address 10.20.20.1/24?

A.
R1(config)#interface ethernet0/0
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0

B.
R1(config)#interface ethernet0/0.20
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0

C.
R1(config)#interface ethernet0/0.20
R1(config)#ip address 10.20.20.1 255.255.255.0

D.
R1(config)#interface ethernet0/0
R1(config)#ip address 10.20.20.1 255.255.255.0

 

 

Which function does an SNMP agent perform?

A. It sends information about MIB variables in response to requests from the NMS
B. It manages routing between Layer 3 devices in a network
C. It coordinates user authentication between a network device and a TACACS+ or RADIUS server
D. It requests information from remote network nodes about catastrophic system events

 

 

What are two roles of the Dynamic Host Configuration Protocol (DHCP)? (Choose two.)

A. The DHCP server assigns IP addresses without requiring the client to renew them.
B. The DHCP server leases client IP addresses dynamically.
C. The DHCP client can request up to four DNS server addresses.
D. The DHCP server offers the ability to exclude specific IP addresses from a pool of IP addresses.
E. The DHCP client maintains a pool of IP addresses it can assign.