Free CCNA 200-301 Dumps 2026

 

Which interface condition is occurring in this output?

• A. duplex mismatch
• B. high throughput
• C. bad NIC
• D. queueing

 

 

 

Refer to the exhibit. PC1 tries to ping PC3 for the first time and sends out an ARP to S1. Which action is taken by S1?

 

 

 

An administrator is configuring a Cisco Catalyst switch so that it will accept management connections only from hosts in the 203.0.113.0/24 network. Other traffic passing through the switch must transit without interruption. Which two configurations must the engineer apply to the router? (Choose two.)

 

 

Refer to the exhibit. PC1 regularly sends 1800 Mbps of traffic to the server. A network engineer needs to configure the EtherChannel to disable Port Channel 1 between SW1 and SW2 when the Ge0/0 and Ge0/1 ports on SW2 go down. Which configuration must the engineer apply to the switch?

 

 

 

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology
–

Tasks
–

All physical cabling is in place. Configurations should ensure that connectivity is established end-to-end.

1. Configure a route on R1 to ensure that R1 prefers R2 to reach the 2001:db8:41::/64
network
2. Configure a floating route on R1, and ensure that R1 uses R3 to reach the 2001 :db8:41::/64 network if the connection between R1 and R2 is down
3. Ping and traceroute should be working

Answer:

 

 

 

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology
–

Tasks
–

All physical cabling is in place. A company plans to deploy 64 new sites. The sites will utilize both IPv4 and IPv6 networks.

1. Subnet 10.30.64.0/19 to meet the subnet requirements and maximize the number of hosts
• Using the second subnet
– Assign the first usable IP address to e0/0 on Sw101
– Assign the last usable IP address to e0/0 on Sw102

2. Subnet 2001:db8::/56 to meet the subnet requirements and maximize the number of hosts
• Using the second subnet
– Assign an IPv6 GUA using a unique 64-Bit interface identifier on e0/0 on Sw101
– Assign an IPv6 GUA using a unique 64-Bit interface identifier on e0/0 on Sw102

Answer:

 

 

 

 

DRAG DROP
–

Drag and drop the characteristic from the left onto the IPv6 address type on the right.

 

 

 

 

 

Which Rapid PVST+ feature should be configured on a switch port to immediately send traffic to a connected server as soon as it is active?

 

 

 

 

 

Which interface is used to send traffic to the destination network?

• A. F0/2
• B. F0/20
• C. F0/12
• D. F0/10

 

 

What is a characteristic of a Layer 2 switch?